What is a User ID ?

A User ID is a user name and password that can be used to access several Honeywell Web sites.

Creating a User ID will simplify your Honeywell online application experience by allowing you to access Honeywell sites with a common username and password. You can choose your own username, password, and security questions; this will help make it easy to remember your account information.

Creating a User ID and Password

You must first provide some basic account information. All fields marked with an asterisk * or "Thumbs down/up" symbol are required and include an easily-remembered User ID, Password, First name, Last name, and Email address. To help protect your account, you must also provide three Security Questions and Answers. You provide the Password, Email address, and each Security Answer twice to help avoid accidental typos.

How to choose a User ID ?

Must be between 6 and 64 characters long
Cannot include the following symbols : @, &, ', <, >, !, ", /, #, $, %, +, ?, (, ), *, [ , ] , \ , { , }
Cannot contain spaces, tabs, or consecutive underscores, i.e. __
Cannot contain elements that imply an email address or URL, such as ".com", ".net", ".org", ".edu" or any variation (e.g. "_com" or "-com")
Cannot start with underscore '_', dash '-' or period '.'
Cannot contain the words "honeywell", "honey" or "allied"
Cannot contain single letter followed by numbers

Password Rules

Must be between 8 and 56 characters long
Must contain only characters from at least three of the following five categories:
- English uppercase characters (A - Z)
- English lowercase characters (a - z)
- Base-10 numeric digits (0 - 9)
- Non-alphanumeric (for example: !, $, #, or %)
Cannot contain three or more consecutive characters from the User ID

Security Question Rules

Each security question must satisfy the following rules:

Must be between 10 and 50 characters long
Cannot be the same as any other security question
Should contain characters from at least three of the following categories:
- English uppercase characters (A - Z)
- English lowercase characters (a - z)
- Base-10 numeric digits (0 - 9)
- Character: question mark '?', single-quote ''', dash '-' or comma ','

Security Answer Rules

Each security answer must satisfy the following rules:

Must be between 3 and 20 characters long
Cannot contain any word in the question
Cannot be the same as any other security answer
Note: Security answers are not case sensitive.

Li-ion Tamer Sensor MOS

LT-SEN-MOS

The Li-ion Tamer Sensor Multi Output Solution (MOS) is a device that detects hydrogen gas, which is generated during thermal runaway of lithium-ion batteries. The detection of hydrogen allows proper management of flammable gas accumulation to avoid explosive conditions. It is also capable of detecting the initial venting of battery electrolyte solvent vapours (off-gassing phase) that occurs early in the failure mode of lithium-ion batteries. The early detection of such events allows proper mitigation steps to be taken to avoid a catastrophic thermal runaway failure.

Features & Benefits
Technical Data
Accessories
Documents

• Early warning of lithium-ion battery failures
• Enable thermal runaway prevention with proper mitigation actions
• Single cell failure detection without electrical or mechanical contact of cells
• Extended product lifetime
• Calibration-free product (only requires bump test)
• Highly reliable output signal
• Low power consumption
• Cost Effective solution for modular Battery Energy Storage Systems (BESS)
• Compatible with all lithium-ion battery form factors and chemistries
• Easy installation
• Independent and redundant perspective on battery health
• Reduction/removal of false positive signals
• Support 2 alarm relay outputs and 1 fault relay output
• Configurable communication protocols including Relay outputs and Modbus/Canbus selection communication

Dimensions [mm]	140 (L) x 85 (W) x 34 (H)
Input Power Range	15 - 32VDC Typical 24VDC
Max. Sensors per Module	1
System Outputs	3 Relay outputs/MODBUS/CANBUS
Current consumption (with Sensors)	65mA, Max 1.56W (@ 24VDC)
Relay Load	Max. 30 VDC 2A; Max. 125 VAC 0.5 A
Output	RJ45 0.25W (5VDC/ 0.5mA) power supply for sensor
Temperature	40 °C to 50 °C
Humidity	5 % to 90 %RH (non-condensing)
Max. Temperature Change	8.6 °C/min

Spare parts:
LT-SEN-IM-UL Li-ion Tamer Interface Module UL
LT-SEN-M Li-ion Tamer Gen 2+ Sensor

Austria	German
Czech Republic	Czech
Poland	Polish
Romania	Romanian
Russia	Russian
Slovakia	Czech
Turkey	Turkish
Ukraine	Russian

Europe

Business

Li-ion Tamer Sensor MOS

LT-SEN-MOS

Features & Benefits

Technical Data

Accessories

Documents